Xilinx Ecm Driver
The Linux USB gadget sub-system supports USB device functionality, including USB networking.
- 10Debugging and resolving common errors
Configure hardware for USB OTG or USB device support
Depending on your hardware, you can use either USB OTG or USB device to enable support for USB networking.
- DM365 - How to configure DM365 for USB host, device and OTG support
Xilinx Platform Cable USB → ドライバー → アンインストール をクリックします。 2) USB ケーブルを一旦取り外してから、もう一度差し込んで、ケーブルをリセットします。 3) iMPACT を起動し、USB ケーブルを接続します。. Windows の プログラムの追加または削除 を使用して ISE Design Suite ツールをアンインストールできません。ツールのアンインストール方法を教えてください。.
Build USB Ethernet network gadget driver
The USB Ethernet network gadget driver caused the device to appear to be a USB network dongle when connected to a host computer. Generally it is best to build USB gadget drivers as modules instead of building them into the kernel so you can unload one and load another.
If you want the target to mount a host PC directory using NFS, then also enable NFS mount support in busybox:
Build the SDK and install the new images to the target hardware.
The Xilinx mailbox driver. This driver supports the Xilinx Mailbox device. 1.01a ecm 08/19/08 Fixed CRs 466320, 466322, 476535, 476242, 476243 new rev 2.00a hm 04. For me, neither Lab Tools 14.7 nor Vivado Lab 2016.2 are able to detect the DLC10 cable when new windrvr6.sys driver is in place. (even though the Device Manager shows no problems with attached USB devices, and yellow/green LED on DLC10 is on). 1) Disconnect all Xilinx USB cables from the host computer. 2) Open a shell or terminal console. 3) Extract the driver script and its support files to a local drive of the machine where the cable will be used by typing.
Load USB Ethernet network gadget driver
After booting the target hardware to a shell prompt, run:
and you should see output similar to:
You can then verify the usb0 network interface exists:
with output similar to:
Connect device to host PC
Before connecting the target device to the host PC, watch the syslog, by running the following command on the host PC:
/download-autocollage-full-version-free.html. Connect the USB cable between the target device and the host PC. The messages file on the host PC should indicate the new USB device was detected.
On the host you can verify the new usb0 interface exists by running:
with the output being similar to:
When you connect the cable, in the target device console, you should see:
Assigning IP addresses
For this simple example, fixed IP addresses are assigned to the both the host PC USB network interface and the target device USB network interface.
On the host
with an entry from the route output that looks like
On the target device
with the route showing the default gateway is using usb0
Verifying network connectivity
Xilinx Ecm Driver Download
On the target device, ping the host PC:
On the host PC, verify the number of packet sent and received is not zero
Look at the values of RX packets: and TX packets:.
Bridging host PC to allow device to reach the Internet
If your host PC is connected to the Internet (through WiFi or Ethernet), then you can allow the target device to share the host PC's Internet connection. The following shows how to enable, test, and disable. It only works if your host PC doesn't have a firewall enable. There is a lot of information on how the Internet giving more detailed explanation.
On the host PC:
And then for reasons I don't fully undestand, I had to configure usb0 on the host again:
On the target device:
To disable forwarding network packets on your host PC:
Configuring a DNS name server
If you need to resolve DNS names, you can configure your target hardware to use Google's DNS server via:
and you can test that names get resolved by pinging some computer on the Internet:
Mounting NFS file system
If you have already enabled NFS share of your development directory target file system, $DEVDIR/fs/fs, then you can easily mount the file system on the target. This is different than a root NFS mount. With a root NFS mount, networking has to be available when the kernel is booting. With a normal (non root file system) NFS mount, you are simply mounting a shared directory somewhere in the target device's file system.
First verify you build the target file system kernel with NFS enabled:
with expected output
Mount host file system on target:
Debugging and resolving common errors
Wireshark
Wireshark is your friend. Run wireshark on your host PC monitoring the usb0 interface and you don't need any packet filters. If something isn't working, you will see the last packet that was sent and not responded to. That will give you a big hint as to where to start looking for the problem.
NFS mount failed reason given by server: Permission denied
Xilinx Ecm Driver Installer
If you see a message like
and you know you have root NFS working, the cause is due to a different sub-LAN address being used. On your host PC, you need to make sure the 10.0.1.* sub-LAN is exported. Run the following commands to export you home directory to all computers on this sub-LAN: